Clearance Specials
These CLEMCO blast nozzles are venturi shaped with a tungsten carbide liner, natural rubber jacket and dual-compound hard rubber threads.
Thread size and entry dimensions vary with nozzle series.
Includes one nozzle washer.


Purpose
A blast nozzle accelerates the air and abrasive as the mixture exits the end of the hose.
The taper and length of the nozzle's inlet and outlet determine the pattern and velocity of the abrasive exiting the nozzle.
The composition of the liner material determines itsmore
Unit of Measure

Specifications

Manufacturer


CLEMCO

Description

TSP-5 Nozzle 5/16" Oriface x 6 1/4" Long 1 1/4" Thread

Brands

Apollo Clemco®

Model

TSP-5

Thread Type

Fine Thread 1-1/4 in.

Nozzle Orifice

5/16 in

Flow Rate at 100 Pounds Per Square Inch (psi) Pressure

137 ft³/min

Length

6-1/4 in

Weight

1.5 lb

Holder

HEP Series

Washer

NW-4

Entry Size

1 in

Liner Material

Tungsten Carbide

Liner Style

Venturi

Jacket Material

Rubber

Color

Green and Black

Requirement for Operation

N/A Nozzles are sized by the diameter of their orifices in 1/16-inch increments. A No. 2 nozzle has a 2/16-inch (1/8-inch) orifice, a No. 3 nozzle has a 3/16-inch orifice, etc. The size of the nozzle orifice determines abrasive and air consumption. Air consumption is measured in cubic feet per minute (cfm) at a given pressure. See the air and abrasive consumption chart.
When choosing a nozzle, consider the amount of available air in cfm, the capacity of the blast machine and the inside diameter of the piping, and the blast and air hoses. For optimal performance, these elements must be compatibly sized.
If too large a nozzle for the compressor is used, low blast pressure will occur. If too large a nozzle for the blast hose is used, rapid wear on the blast hose will occur. If too small a nozzle is used, smooth media flow will be difficult to achieve.

Advantages

N/A

  • Short-venturi nozzles (TJP, TYP) designed for blasting 12 to 18 inches away from the surface.
  • Long-venturi nozzles (TSP, TMP, TXP) allow high production blasting at a distance of 18 to 24 inches for hard to- clean surfaces, and 30 to 36 inches for loose paint and soft surfaces
  • Expected life with expendable abrasives is approximately 300 hours
  • Durable natural rubber jacket
  • 1 inch entry provides smooth transition and maximum productivity with 1 inch ID blast hose
  • 1 1/4 inch entry ensures maximum productivity with 1 1/4 inch ID blast hose

Component Compatibility Guide

N/A

No. Nozzle Orifice Recommended cfm Range Min. Blast Machine Capacity Min. Piping ID Blast Hose ID Min. Air Hose ID
3 3/16" 45 - 81 2 cu ft 1" 3/4" 1"
4 1/4" 81 - 137 2 cu ft 1" 1" - 1 1/4" 1 1/4"
5 5/16" 137 - 196 4 cu ft 1" 1" - 1 1/4" 1 1/4"
6 3/8" 196 - 254 6 cu ft 1 1/4" 1 1/4" 1 1/2"
7 7/16" 254 - 338 6 cu ft 1 1/4" 1 1/4 - 1 1/2" 2"
8 1/2" 338 - 548 6 cu ft 1 1/4" 1 1/2" 2"

Note: Best performance is obtained when sizes of nozzle, blast machine piping, blast hose and air hose are properly matched.
  • Cfm range is based on blasting at 100 psi for the life of the nozzle.
  • Blast machine capacity should allow 20 to 30 minutes of blasting.
  • Hose ID should be three to four times the size of the nozzle orifice.

Note

Note

All threaded nozzles include one nozzle washer.